FAG 2315-M self-aligning ball bearing
- Brand
- FAG
- Category
- Bearings
- Subcategory
- Self-aligning ball bearings
We reply promptly.
Tell us the quantity you need and request a quote by WhatsApp or email.
Can't find the exact model? Tell us the part number or model you need. We'll track it down and quote it, whether or not it appears in our catalog.
Decoding FAG 2315-M
- 23Series
- Self-aligning ball bearings, 23 series. Series differ in outside diameter and width even when the bore is the same.
- 15Bore
- Bore 75 mm (15 × 5).
- MSuffix
- FAG suffix: identifies the variant, such as seals or shields, cage, internal clearance or other features.
2315 is the standard ISO basic designation, which sets the bearing type, series and bore.
Description
FAG 2315-M measures 75 mm across the bore and 160 mm across the outside diameter; its width is 55 mm (75 x 160 x 55 mm).
FAG 2315-M belongs to self-aligning ball bearing, part of our Bearings range. Tell us how many you need by WhatsApp or email and we'll get back to you promptly with a quote for 2315-M and any equivalents.
FAG self-aligning ball bearings handle shaft misalignment that a standard deep groove ball bearing cannot. Inside, two rows of balls run on a spherical raceway in the outer ring, so the bearing follows slight angular deflection of the shaft relative to the housing instead of fighting it. This makes the design a practical choice where alignment is imperfect or where the shaft bends under load.
The series designation combines a size code with the suffix -M, as in 1219-M, 1220-M or 1230-M. The number is not a bore, outer diameter or width; it is a reference that has to be looked up in a dimension table. The -M suffix identifies a solid brass cage, the standard construction for this line. When requesting a quote, send the full part number exactly as it appears on the drawing or on the bearing you are replacing.
Typical applications include industrial fans, centrifugal pumps, conveyors, mixers and transmission equipment, where mounting tolerances, shaft flexing or thermal growth can push the shaft out of line. In service, the self-aligning behavior lowers parasitic loads on the shaft and on the support, and it eases installation when the housing bore is not perfectly concentric with the shaft.
Selection comes down to the radial and axial loads the bearing will carry, the operating speed and how much misalignment the equipment has to absorb. Internal clearance and cage type also matter for high-speed running and lubrication. At mounting, keep the housing and shaft clean, confirm the fits are correct, and apply the grease or oil quantity and grade suited to the operating conditions.
Equivalent self-aligning ball bearings from other brands exist with the same designations and dimensions. Whether they interchange depends on matching main dimensions, cage type and internal clearance. If a part number from one brand does not line up exactly with another, compare the dimension tables rather than trusting the number alone. Send the original part number and the housing dimensions and we can help confirm the match.
Dimensions
75 x 160 x 55 mm (d x D x B): boundary dimensions for basic designation 2315, according to ISO 15.
- Bore
- 75mm
- Outside diameter (D)
- 160mm
- Width (B)
- 55mm
SKF and other brands, same size
Other brands' pages with basic designation 2315: 75 x 160 x 55 mm (d x D x B) per ISO 15.
What they share are the ISO 15 boundary dimensions, not the specs: seals or shields, internal clearance, cage and load rating may vary with brand and suffix. Every quote is by full part number.
Frequently asked questions
- FAG 2315-M bearing: what are its dimensions?
- FAG 2315-M measures 75 mm across the bore and 160 mm across the outside diameter; its width is 55 mm (75 x 160 x 55 mm). Those are the boundary dimensions standardized in ISO 15 for basic designation 2315.
- What does the -M suffix indicate on these bearings?
- It identifies a solid brass cage, which is the standard design for this series. That construction detail affects high-speed behavior and mechanical strength. Send the specific part number by WhatsApp or email and we will confirm the exact design.
- How can I tell what size a 1220-M bearing is?
- The number is a size code, not a measurement. You need the manufacturer's table to translate it into bore, outer diameter and width. Send us the part number or the shaft and housing dimensions and we will guide you.
- Is it possible to replace it with a bearing from another brand?
- Yes, provided the main dimensions, cage type and internal clearance match. Cross-brand interchange is confirmed by comparing dimension tables, not by the number alone. Send the original part number and dimensions so we can check the equivalent.